DescriptionSTD-RCF 4 Rolling Contact Fatigue & Bearing Friction Rig may be used for both endurance
WhatsApp : +86 13816217984
Email : info@qinsun-lab.com
STD-RCF 4 Rolling Contact Fatigue & Bearing Friction Rig may be used for both endurance testing and precision bearing frictional loss measurement. Two test assemblies are available:
• combined radial and axial loading
• bi-directional axial loading
Load is applied by means of servo controlled pneumatic bellows with force transducer feedback.
An in-line torque transducer is provided for friction measurement, with a maximum permissible speed of 10.000 rpm.
Bearing outer race temperatures are measured with thermocouples and a vibration sensor with adjustable level trigger circuit is provided for stopping the machine at the on-set of rolling contact fatigue.
An integral lubricant service module is fitted as standard incorporating a sump tank with immersion heater, delivery pump, scavenge pump, oil to water heat exchangers for cooling and change-over filters.
| Technical Specifications | |
| Motor: | 4 kW a.c. vector motor and drive with encoder feedback |
| Maximum Motor Speed: | 3.000 rpm |
| High Speed Drive: | Flat belt |
| Ratio: | 6.7:1 |
| Low Speed Drive: | Timing belt |
| Ratio: | 1:2 & 2:1 |
| Maximum Spindle Speed: | 10.000 rpm |
| Torque Transducer Range: | 50 Nm |
| Maximum Lubricant Supply Rate: | 6.8 l/min |
| Maximum Lubricant Supply Temperature: | Ambient to 150°C |
| Change-over Filters: | 3 micron |
| Interface: | Phoenix Tribology USB micro-controller interface |
| Software: | COMPEND 2020 |
| Controlled Parameters | Motor speed |
| Applied loads | |
| Test fluid temperature | |
| Test duration | |
| Recorded Parameters | Motor speed |
| Applied load | |
| Total bearing friction | |
| Lubricant inlet temperature | |
| Bearing outer race temperatures | |
| Vibration sensor output | |
| RCF 4/1 Combined Radial and Axial Loading | |
| Configuration: | Four bearing back-to-back |
| Bearing Types: | Taper, spherical, cylindrical roller, angular contact, deep groove ball |
| Shaft Diameters: | 40 mm to 65 mm |
| Maximum Bearing Outside Diameter: | 140 mm |
| Maximum Axial Load per Bearing: | 16 kN |
| Maximum Radial Load per Bearing: | 40 kN |
| Maximum Axial Load: | 16 kN |
| Maximum Radial Load: | 80 kN |
| RCF 4/2 Test Assembly – Bi-directional Axial Loading | |
| Configuration: | Two deep grove ball bearings back-to-back |
| Bearing Types: | Deep grove and angular contact (uni-directional loading) |
| Shaft Diameters: | 20 mm to 40 mm |
| Maximum Bearing Outside Diameter: | 90 mm |
| Maximum Axial Load Per Bearing: | 4 kN |
| Maximum Axial Load: | 4 kN |
| Services | |
| Electricity: | 415 V, three phase, 50/60 Hz, 7.5 kW |
| Clean, dry air: | 4 cfm at 8 bar (120 psi) |
| Mains water and drain: | 10 l/min (typical) |
Disclaimer: Le contenu ci-dessus est destiné à des fins de référence et de communication uniquement entre les initiés de l'industrie, et ne garantit pas son exactitude ou son exhaustivité. Conformément aux lois et règlements pertinents et aux règlements de ce site Web, les unités ou personnes qui achètent des articles connexes doivent obtenir des qualifications et des conditions de qualification valides.
Téléphone de l'entreprise
+86-21-6420 0566
Heures de travail
Du lundi au vendredi
Téléphone portable:
13816217984
Courriel :
info@qinsun-lab.com
